ProtexSafe Electronic Keypad Wall Safe (PWS-1814E)-Black, Burglary Resistant wall safe, digital electronic locking system, velvet interior, automatic door opening, 2 Removable shelves

I just spent the entire day installing this safe and am not quite done with covering all tracks of the construction surgery due to all the suitable wall spaces in my old house having studs at considerably less than standard 16"o.c. distance.That little contretemps aside, this product is first rate. Sturdy, easy to use (and to install, if you live in a modern house), this heavy safe looks and feels sturdy and crowbar-proof, yet has a pleasing interior thanks to a velvety interior cladding. Punch in your personal 4-digit code and the door springs open on its own and illuminates the safe interior through a hidden LED light. The effect is almost magic and very inviting. There is also a 6-digit override code in case you forget the 4-digit code. Both are easy to reprogram from their factory settings. While the locking mechanism requires 4 AA batteries to work, there is a secondary exterior battery compartment that can be used in the unlikely case that the interior batteries run out. You would have to ignore the low-battery warnings or not use the safe for a long time for that to happen. Finally, there is a set of rather odd-looking keys to open the safe the old-fashioned way if all of the above were to fail. My biggest worry at this minute is where to store these keys so I would find and identify them if ever needed, but in a place a burglar would not bother to look... I am thinking my safe at the bank.Now to some practical installation hints, as the instructions are very sparse in this respect. First, you need to find a suitable placement from a comfort point of view. The door hinges are on the right and cannot be switched. The safe requires a rectangular opening in the wall, 18-1/8 by 14-1/8 inches. 14 1/8 inches is the surface-to-surface distance between studs in standard construction, and you *will* need side studs to bolt the safe into.Next, you need to identify where the studs are in your preferred spot. A studfinder works best, but knocking the wall with your knuckles can also work if you have an ear for hollow vs. solid sounds. Once you ascertain the proper space, explore the supposedly hollow space between the two studs for any firebreaks (horizontal spacer studs), again with a studfinder or your knuckles and your ear. If you find one, you will likely want to place the safe immediately above it.Once you have a rough idea of the safe's location, make a small pilot hole with a drill, then stick a wire (or disassembled coathanger) into it to plumb the depth. The safe requires 3 3/4 " unobstructed depth, measured from the wall surface facing the room. Assuming all is good so far, draw the outline of the required opening with light pencil on the wall. Next, drill pilot holes at 1 to 2 inches apart along the outline. You want to insure that there are no hidden obstacles anywhere. Small drill holes are a lot easier to patch up then a large hole. The pilot holes will also help you identify the exact location of stud edges and firebreak edge, if any. As you draw the final, verified outline of the opening, make sure that the angles are square! Ideally you have a helper hold the (heavy) safe against the wall you you run a pencil around its outline. A heavy, strong person might be able to do so without help in a pinch.Finally you are ready to cut. For regular sheetrock (gypsum board) used starting in the 1950s, a handsaw is best. Ideally you hold the business end of a household vacuum hose (without attachment) immediately below the saw blade as it works through the sheetrock, as this dust will otherwise have a way of coating every square inch of surface within sight. If, however, you have lath and plaster as I did in my old house, you will need an electric reciprocating saw ("sawz-all") with a short, "bimetal" blade to cut cleanly through the hard gypsum and the wood slats. Err on the side to make the hole about 1/8" wider and taller than the outline of the safe. One more hint: Make a 3 x 3 hole in the center first, then peer around inside for any pipes or wires you may have missed. Flexible romex wire may likely and safely fit behind the safe, but pipes my force you to retreat and find an alternate location.Once you are done with the cutting, if you are lucky, the safe will pop in cleanly into your opening. If you are like me and made the opening too tight, you'll have to cut a little more. With the open safe fitting snug against the wall, mark the 3 drill holes on the left side against the left stud, and repeat the same with the 3 holes against the right stud. Drill holes smaller than the supplied bolts -- you can always re-drill with a larger bit if needed. Don't forget to add the supplied washers as you insert the bolts into the holes you drilled. You will need a socket wrench (I used 17 mm -- 5/8 or 11/16 *might* work, also) with a ratchet arm to do these bolts justice. Remove the velvet shelves while you do this.Once you are done and the safe is installed, vacuum it out and paint any damaged wall surface surrounding it though, if you were very careful, that may not be necessary. Enjoy!

We're very happy with the quality of this safe, it feels very sturdy and is very easy to use. The steel is sturdy, and the keypad doesn't feel cheap at all. The buttons are actually plastic, and don't feel flimsy or cheap at all. I also like the digital readout of the keypad digits as they're pressed. The "user code" works like a hotel safe where you enter a code while the door is open then press * to close. The user code will open it the next time, but must be re-entered to close it. It also comes with a "master code" that will always open and close the safe, and it is re-programmable. I read some reviews that the keypad is loud, and I would agree it is moderately loud. Not loud enough to be annoying, but loud enough that anyone could hear it in the house when its dead quiet. I put mine in our master closet, so with my setup, it's less audible outside of my bedroom.The door actually swings out nicely when you open the lock, about a couple inches. Enough to comfortably grab the door and open it the rest of the way. The felt lined interior is nice, and there's even a little LED light in there. It's almost luxurious. Real nice to open and use. I was also surprised how little it comes out of the wall. I didn't measure, but it can't be more that 1/4-1/2". It feels like it's just part of the wall!Installing this was a bit of a pain, but that's only because my studs were 16" apart from the edges, not the center. I had to get a 2x4, cut a 2' section off, then cut off another 1/4" to get it to fit in place. Overall, it probably took me 2-3 hours to install, but again that's because I needed to cut a filler piece. I was also using a hand saw to cut the 2x4 and a utility knife to cut the sheetrock, I'm sure if I used the more appropriate tools it would have taken significantly less time. But if your studs are 16" on center, its a cinch. Just measure out where you want it on your wall, use a level to draw your lines, cut, insert, drill some pilot holes, then screw it in. If you're handy at all, I would recommend that you install this yourself and save yourself the $200+ to have amazon get a professional to install it. You'll probably do a better job anyway.

This is one of our best purchases for our house, ever. If we move, I'm taking it with us. As opposed to putting some kind of cabinet lock on the dresser, this solution was "perfect." It is a quality product with everything you want but adjustable shelves. The install is already "do it yourself" friendly. I installed it in under an hour. I took my time. An extra pair of hands during install would be nice, but I did without. I installed a firebreak 2x4 at the bottom of my square hole, so the safe sits on solid wood. Slide the safe in, and use a screw gun to put in some small temporary screws while you position the large lag screws later. It goes pretty easily. Press your 4 digit code and it springs open with the timer LED light inside. These are welcome features. If you're retrieving a handgun at night, it is quickly retrieved with the magazine. At the same time it is safe from curious little hands 24/7. I wouldn't store the "Hope Diamond" in this thing, but it works great for what it is for passports, papers, handguns, etc. FOR OUR HOME IT WAS PERFECT. You use the backup battery pack to get the safe opened and install the keyboard batteries. The over-ride keys are pick proof, and a nice manual feature when all else fails. Be sure to hide your battery pack and keys. The safe works on two codes that you can program, a daily 4 digit one and a six digit master for just in case you forget the other. It's well thought out, and really nice looking after installation. YOU CAN PUT A FRAMED PICTURE OVER YOUR INSTALL TO LOWER TEMPTATION.

Easy to fit works a trsat

Worked perfectly when I received it. The next day, I receive an error message saying ‘b loc.’ Tried everything to fix this including consulting with Protex. I do not recommend this product.

I bought this safe as a gift for my husband and we couldn't be happier with it. Installation was easy. The 6 bolts that are screwed into the wall studs is fantastic security, that safe isn't going anywhere. It installs quite flush with the wall, extending out by only 1 or 2 mm. For added protection you can hang a piece of art on hinges over top of it.If you open it the dark a light goes on inside for a few seconds so you can see what you're doing. There is plenty of storage space for documents, passports, jewelry, etc. The "low battery" indicator does come on sooner than I would have expected, however that was months ago and I still haven't had to change the batteries. It simply gives you ample time to go buy new ones. Having the key backup provides peace of mind, but I have never had to use it.Overall this is a fantastic product and I would recommend this to anyone.

Very solid, heavy duty construction. Installed easily. I was skeptical about the cruciform lock but it is recessed deeply enough to make picking difficult. Well thought out design, I like the ability to power the unit externally. When you use the number display block it still blocked until you undo it.I like that. The only future feature I would like to see would be the ability to have numerous codes, rather than just one code and the master one. I noticed that some members complained about the factory code, well if you read the instructions it shows how to change the master code to one of your choice. READ THE INSTRUCTIONS

Really nice solid and easy to install